TÜRK STANDARDI
|
|
TS No :
|
TS EN ISO 19063-1
|
|
|
Kabul Tarihi :
|
18.04.2016
|
|
Hazırlık Grubu :
|
Teknik Kurul |
|
Doküman Tipi :
|
|
|
Yürürlük Durumu :
|
U (Yürürlükteki Standard/Standard) |
|
Başlık :
|
Plastikler - Darbeye dayanıklı polistiren (PS-I) kalıplama ve ekstrüzyon malzemeleri- Bölüm 1: İşaretlerle gösterme sistemi ve özelliklerin dayandığı temeller |
|
Başlık (İng) :
|
Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications |
|
Kapsam :
|
- |
|
Kapsam (İng) :
|
This part of ISO 19063 establishes a system of designation for impact-resistant polystyrene (PS-I)
moulding and extrusion materials, which may be used as the basis for specifications.
The types of impact-resistant polystyrene plastic are differentiated from each other by a classification
system based on appropriate levels of the designatory properties:
a) Vicat softening temperature;
b) melt mass-flow rate;
c) Charpy notched impact strength;
d) flexural modulus;
and on information about composition, intended application and/or method of processing, important
properties, additives, colorants, fillers, and reinforcing materials.
This part of ISO 19063 is applicable to all impact-resistant polystyrene plastics with a two-phase
polymer system comprised of a continuous phase, consisting of polystyrene and/or a copolymer of
styrene with an alkyl-substituted styrene, and a dispersed elastomeric phase based on butadiene.
It applies to materials ready for normal use, unmodified or modified by colorants, additives, fillers, etc.
This part of ISO 19063 does not apply to expandable materials.
It is not intended to imply that materials having the same designation give necessarily the same
performance. This part of ISO 19063 does not provide engineering data, performance data, or data on
processing conditions which may be required to specify a material for a particular application and/or
method of processing.
If such additional properties are required, they will be determined in accordance with the test methods
specified in ISO 2897-2, if suitable.
In order to specify a thermoplastic material for a particular application or to ensure reproducible
processing, additional requirements may be given in data block 5 (see 3.1). |
|
Yerini Aldığı :
|
TS 3423-1 EN ISO 2897-1 :2000; |
|
Yararlanılan Kaynak :
|
EN ISO 19063-1:2015 |
|
Uluslararası Karşılıklar :
|
EN ISO 19063-1-EQV |
|
ICS Kodu :
|
83.080.20 Termoplastik Malzemeler |
|
Atıf Yapılan STD :
|
TS EN ISO 1043-1 :2012; TS EN ISO 1043-2 :2012; TS EN ISO 2897-2 :2006; |
|
Cen/Cenelec :
|
CEN |
|
Dili :
|
en |
|
Renk Durumu :
|
Siyah-Beyaz |
|
Uygulama Durumu :
|
Yürürlükte |
|
Sayfa Sayısı :
|
19 |
|
Fiyatı :
|
56,00 EURO (1.941,50 TL + %10 Kdv) |
| Çakışan Standart Varsa İptal Tarihi (DOW) | - |
|