|
|
|
Standard Detayı
|
İptal Standard
TÜRK STANDARDI
|
|
TS No :
|
TS EN 1594
|
|
|
Tercüme Tarihi :
|
24.03.2015
|
|
Kabul Tarihi :
|
13.02.2014
|
|
İptal Tarihi :
|
4.03.2024 |
|
Hazırlık Grubu :
|
TK22: Tesisat ve Basınçlı Kaplar Teknik Komitesi |
|
Doküman Tipi :
|
|
|
Yürürlük Durumu :
|
H (İptal Edilmiş Standard/Withdrawn standard) |
|
Başlık :
|
Gaz sistemleri - En yüksek işletme basıncı 16 bar’ın üstünde olan
boru hatları için - İşlevsel özellikler |
|
Başlık (İng) :
|
Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements |
|
Kapsam :
|
Bu standard, EN ISO 13686’ya uygun toksik ve korozif olmayan, işleme tâbi tutulmuş doğal gazın 16 bar’ın üstündeki en yüksek işletme basıncında (EYİB) taşınmasında kullanılan kara üzerindeki gaz besleme sistemlerine ait boru hatlarını kapsar.
Bu standard, EN ISO 13686’ya uygun enjekte biyometan gibi konvansiyonel olmayan gazların taşınması için 16 bar’ın üstünde en yüksek işletme basıncındaki ayrıca gazı oluşturan diğer maddelerin ve gaz özelliklerinin boru hattının bütünlüğünü etkilemeyecek şekilde işlevsel gereklerin ayrıntılı olarak teknik değerlendirmesi yapılan boru hatlarına da uygulanabilir. |
|
Kapsam (İng) :
|
This European Standard is applicable to pipelines with a maximum operating pressure (MOP) over 16 bar for the carriage of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 in onland gas infrastructure. This European Standard is also applicable to pipelines with a maximum operating pressure (MOP) over 16 bar for the carriage of non-conventional gases such as injected biomethane, complying with EN ISO 13686 and for which a detailed technical evaluation of the functional requirements is performed ensuring there are no other constituents or properties of the gases that can affect the integrity of the pipeline. Onland gas infrastructure is where:- pipeline elements are made of unalloyed or low-alloyed carbon steel; - pipeline elements are joined by welds, flanges or mechanical couplings; - the pipeline is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises; - the design temperature of the system is between -40 °C and 120 °C inclusive. This European Standard applies to onshore pipeline systems from the point where the pipeline first crosses what is normally accepted as battery limit between on and offshore, e. g.; - first isolation valve; - the base of steep sea shelf; - above the high water/low water mark onto mainland; - an island. This European Standard also applies to a pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes etc. This European Standard does not apply to existing pipelines, in use prior to the publication of this European Standard, nor to modifications to existing pipelines. Gas infrastructures covered by this European Standard begin after the gas producer's metering station. The functional demarcation of the pipeline system within a plant area will be determined from case to case. Generally speaking, this will be directly after the first isolating valve of the installation. This European Standard also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar. Welding requirements are described in a special application standard on welding for gas infrastructures EN 12732. Functional requirements for stations are given in: EN 1776, Gas supply systems - Natural gas measuring stations - Functional requirements EN 1918-5, Gas supply systems - Underground gas storage - Part 5: Functional recommendations for surface facilities EN 12186, Gas supply systems - Gas pressure regulating stations for transmission and distribution - Functional requirements EN 12583, Gas supply systems - Compressor stations - Functional requirements This European Standard specifies common basic principles for gas infrastructures. Users of this European Standard should be aware that there may exist more detailed national standards and codes of practice in the CEN member countries. |
|
Yerini Aldığı :
|
TS EN 1594 :2010; |
|
Yerine Geçen :
|
TS EN 1594 :2024; |
|
Yararlanılan Kaynak :
|
EN 1594:2013 |
|
Uluslararası Karşılıklar :
|
EN 1594-EQV |
|
Tercüme Edildiği STD :
|
EN 1594 |
|
ICS Kodu :
|
23.040.01 Boru Hattı Bileşenleri ve Genel Olarak Boru Hatları; 75.200 Petrol Ürünleri ve Doğal Gaz Depolama Ekipmanları |
|
Atıf Yapılan STD :
|
TS EN 1515-3 :2006; TS EN 1759-1 :2010; TS EN ISO 6892-1 :2011; TS EN 10204 :2007; TS EN ISO 3183 :2013; TS EN 10288 :2002; TS EN 10289 :2004; TS EN 10290 :2002; TS EN 10301 :2004; TS EN 12068 :2001; TS EN 12186 :2014; TS EN 12327 :2013; TS EN 12560-1 :2001; TS EN 12560-2 :2014; TS EN 12560-3 :2001; TS EN 12560-4 :2001; TS EN 12583 :2014; TS EN 12732+A1 :2014; TS 5141 EN 12954 :2003; TS EN 14141 :2013; TS EN 16348 :2013; |
|
Cen/Cenelec :
|
CEN |
|
Dili :
|
tr |
|
Renk Durumu :
|
|
|
Uygulama Durumu :
|
Yürürlükten kaldırıldı (Withdrawn Standard) |
|
Sayfa Sayısı :
|
82 |
|
Fiyatı :
|
440,00 TL + %10 Kdv |
| Çakışan Standart Varsa İptal Tarihi (DOW) | - |
|