Logo
 
Standard Arama
Standard Arama Sisteme Giriş
Standard Detayı
Geri |< << >> >|
TÜRK STANDARDI
(Direktif :97/23/EC)
TS No : TS EN 12953-1      
Kabul Tarihi : 2.01.2014
Hazırlık Grubu : TK22: Tesisat ve Basınçlı Kaplar Teknik Komitesi
Doküman Tipi :
Yürürlük Durumu : U (Yürürlükteki Standard/Standard)
Başlık : Silindirik kazanlar - Bölüm 1: Genel
Başlık (İng) : Shell boilers-Part 1:General
Kapsam : Bu standard, hacimleri 2 litreden fazla olan, 110 ºC’dan fazla bir sıcaklıkta ve 0,5 bardan daha büyük müsaade edilebilir basınçta buhar ve/veya sıcak su üretimi için kullanılan silindirik kazanlara uygulanır. Bu standardın amacı, silindirik kazanların çalışması ile ilgili tehlikeleri en aza indirmeyi ve silindirik kazan hizmete alındığında mevcut olan tehlikeleri kapsayacak yeterli korumanın sağlandığını garanti etmektir. Koruma, bu standardın muhtelif yerlerindeki tasarım, imalat, deney ve muayene yöntemlerinin ve tekniklerinin doğru bir şekilde uygulanması ile sağlanır. Uygun olduğunda kalıcı tehlikeler ve yanlış kullanım ihtimali için yeterli uyarı, eğitim ve çalıştırma talimatlarında verilir ve ilgili ekipman yakınında bulundurulur (bk. EN 12953-7 ve EN 12953-8).
Kapsam (İng) : This standard applies to shell boilers with volumes in excess of 2 litres for the generation of steam and/or hot water at a maximum allowable pressure greater than 0,5 bar and with a temperature in excess of 110 °C. This European Standard specifies requirements for both directly fired and electrically heated boilers including Low Pressure Boilers (LPB) as well as for heat recovery boilers with a gas-side pressure not exceeding 0,5 bar of cylindrical design, constructed from carbon or carbon manganese steels by fusion welding and a design pressure not exceeding 40 bar. The boilers covered by this European Standard are intended for land use for providing steam or hot water. Where a particular boiler is a combination of shell and water tube design then the water tube standard series EN 12952 is used in addition to this European Standard. One such example of this combination is shown in this standard. This European Standard applies to the generator, from the feed-water or water inlet connection to the steam or water outlet connection and to all other connections, including the valves and steam and water fittings. If welded ends are used, the requirements specified herein begin or end at the weld where flanges, if used, would have been fitted. This European standard does not apply to the following types of boilers and equipments: a) water-tube boilers; b) non stationary boilers, e. g. locomotive boilers; c) thermal oil boilers; d) boilers where the main pressure housing is made of cast material. e) pumps, gaskets, etc. f) brickwork setting and insulation.
Yerini Aldığı : TS 377-1 EN 12953-1 :2005;  
Yararlanılan Kaynak : EN 12953-1:2012
Uluslararası Karşılıklar : EN 12953-1-EQV
Tercüme Edildiği STD : EN 12953-1
ICS Kodu : 27.060.30 Kazanlar ve Isı Eşanjörleri
Atıf Yapılan STD : TS 377-3 EN 12953-3 :2005;  TS 377-10 EN 12953-10 :2006;  TS EN 12953-13 :2012;  TSE 377-14 CR 12953-14 :2006;  
Cen/Cenelec : CEN
Dili : tr
Renk Durumu : Siyah-Beyaz
Uygulama Durumu : Yürürlükte
Sayfa Sayısı : 35
Fiyatı : 280,00 TL + %10 Kdv
Çakışan Standart Varsa İptal Tarihi (DOW)-